DESCRIPTION
- EasyCare Block-Out Primer/Sealer is a high hiding, high performance product making it an excellent choice for all interior surfaces such as new and unsealed drywall, ceilings, non-staining wood, plaster, brick, stone and concrete surfaces.
- This product is Master Painter Institute certified and is approved for use by the Unites States Government
FEATURES
- Blocks & seals
- Improves adhesion
- Non-spatter formula
- Outstanding coverage
- Use on virtually all interior surfaces
RECOMMENDED USE
- New or unsealed interior drywall, non-staining wood, plaster, brick, stone and concrete surfaces.
- THINNING: Thin sparingly with water if necessary for spraying at a rate of no more than ½ pint per gallon.
- DRY TIME: Dries in 1-2 hours at 77 and 50% humidity. May be top-coated in two hours. Allow 24 hours before sanding. Low temperature or high humidity may increase dry time.
- COVERAGE: Average coverage 300-400 sq. ft. per gallon (3.78L) depending on porosity, surface texture and application method.
- CLEAN UP: Use warm water and soap. Properly dispose of all soiled rags.
- DISPOSAL: ENVIRONMENTAL TIP: Full: Give remaining product to neighbors or community organization. Partially full: (If state or local regulations allow) Pour residue into absorbent material. When dry, dispose of in trash for pick up. Empty: this container may be accepted in a recycling program.
STORAGE: Protect unused product from freezing.
FORMULA ANALYSIS
- Resin Type-Vinyl Acrylic Latex
- Sheen/Type Finish:
- 3-8 @60° / Primer
- Weight per Gallon = 11.38 lbs.
- Percent Solids by Weight = 54.11 %
- Percent Solids by Volume = 41.92 %
- Viscosity Range = 95-100 KU
- V.O.C. = Less than 100 g/l 0.84 lbs./gal.
- MPI Certification – # 50
APPLICATION METHOD
- For specific surface preparation needs see the “Interior Surface Prep” section in this manual Stir thoroughly before and during use
- Do not apply over a surface that has not been properly prepared
- Use product when surface and air temperature are between 50 – 90
- Do not over spread
- Use a high quality 3/8 inch nap roller cover, or nylon/polyester brush
- If applying by roller, roll from dry area into the wet using firm crisscrossing strokes. Finish with long ceiling to floor strokes in one direction
- Paint the ceiling first, then the walls
- Allow new masonry to cure at least 30 days before coating
- Primer may be tinted with up to 2 oz. (59 ml) of colorant per gallon (3.78L).
SURFACE PREPARATION
- Remove loose paint, wash off dirt and grease with detergent.
- Allow to dry thoroughly Scuff sand and dull glossy surfaces
- Patch cracks and spot prime with this product or with StartRight Int/Ext Latex Primer (SRL-1)
- For best results on heavily stained areas, use a coat of StartRight Latex Primer (SRL-1)
- For drastic color changes or deep, vivid colors, primer with StartRight Tintable Primer (BC-1) For other specific surface prep needs, see the “Interior Surface Prep” section of this manual.
WARNING
- CONTAINS CRYSTALLINE SILICA HARMFUL IF INHALED. Inhalation of crystalline silica can cause cancer.
- Risk of cancer depends on duration and level of exposure to dust generated from sanding surfaces or spray mist.
- When sanding or spraying product use. LIQUID PAINT AND VAPOR MAY CAUSE IRRITATION: Use only with adequate ventilation. To ensure fresh air entry during application and drying, open all windows and doors.
- If headache or dizziness is experienced during use leave area for fresh air. DO NOT TAKE INTERNALLY: Paint contains glycol ethers. May be harmful if swallowed in large quantities.
- Avoid contact with eyes, skin or clothing. Can cause irritation. Warning: This product contains chemicals known to the state of California to cause cancer and/or birth defects or other reproductive harm.
- FIRST AID: INHALATION: If excessive exposure symptoms are experienced, leave area to obtain fresh air. If difficulty continues, get medical assistance immediately. Ingestion: Do not induce vomiting. Get medical attention immediately. EYE CONTACT: Flush immediately with plenty of water for at least 15 minutes. SKIN CONTACT: Wash thoroughly with soap and water.
WARRANTY
- This is TrueValue® American Product. Made in USA.
- Limited Warranty Policy: If for any reason you are not completely satisfied with this product, return container with receipt to store where purchased for refund.
- Since application is beyond our control, this policy does not include reimbursement for any labor or other costs. Terms & Conditions apply…
COLORS AVAILABLE
- True Value paint has more than 2,000 paint colors from which to choose. Learn about color schemes and how to come up with great paint color ideas.
- Plese Select Your Colors: COLOR GALLERY: Use our Color Gallery’s virtual paint swatches to choose from a selection of popular paint colors and create a captivating paint palette. Keep it simple with comfortable neutrals, play up accent colors or introduce the bright pop of a complementary color to make a refreshing statement in your home this weekend.
- https://www.truevaluepaint.com/explore-color/color-gallery/
Reviews
There are no reviews yet.