DESCRIPTION
- Penetrating clear satin primer/sealer primarily for verticalsurfaces; water-based acrylic, low odor and low VOC.
FEATURES
- Seal brick, stucco & concrete
- Rejuvenate old brick & plaster
- Brighten aluminum siding
- Prime vinyl siding
- Bind chalky surface
- Paint additive to extend life & coverage
- Buffer pH in hot cement
- Dustproofing and priming floors
- prior to painting
RECOMMENDED USE
- COVERAGE: 80–300 sq.ft. per gal., depending on surface porosity. Second coat application is 50% greater. Two coats are required for waterproofing bare, vertical concrete.DRY TIME: 2–4 hours, depending on temperature and humidity.
- TOPCOATING: May be topcoated with latex, oil-based or elastomeric coating when dry.
- PAINT ADDITIVE: 4–8 oz. of SEAL-KRETE Original can be mixed with one gallon of latex paint to improve spread rate. CLEAN-UP & STORAGE: Clean all tools immediately after use with soap and water. Store unused product in a dry place above 32°F (0°C). KEEP FROM FREEZING.
- LIMITATIONS: Use on above grade vertical surfaces or as a primer on horizontal surfaces – not for below grade use. Do not apply if rain is expected within 12 hours or if temperatures fall below 50°F within 24 hours of application. Do not use on swimming pools, bird baths, water features, cedar, redwood or in areas where hydrostatic pressure is likely to develop.
- Do not use on very porous substrates like low density, decorative block (use SEALKRETE Heavy-Duty instead).
- Sanding or removing paint containing lead may be hazardous. For information contact the National Lead Information Center at 1-800-424-LEAD or www.epa.gov/lead.
FORMULA ANALYSIS
- Solids: 10%
- Proprietary Acrylic Resin
- Water Based
- Odor: Low
- Appearance: Milky White, Dries Clear
- VOC < 49 g/L – EPA Method 24 – Waterproofing Sealer Category
APPLICATION METHOD
- Read “LIMITATIONS” section before use. This sealer is ready to use; do not dilute.
- Apply with a brush, roller or sprayer (garden or airless). Backroll spray applications to ensure penetration.
- Apply at least two coats, allowing two hours dry time between coats. Remove any overspray immediately with water. Note: Sealer goes on milky white but dries clear. COVERAGE GUIDELINES
- Material Coverage
- Approx. sq.ft./gal.
- Stucco/Simulated Brick 150
- Concrete Slab/Tilt-ups 175
- Concrete Blocks 80
- Brick 125
- Wood Fencing 175
- Aluminum Siding 300
- Galvanized Metal 300
- Adobe 100
- Chalky Surfaces 300
- Note: Actual coverage will vary depending on porosity of surface. Use a highsolids formula, like SEAL-KRETE Heavy Duty, for low density, decorative
- block (split-face/fluted block).
SURFACE PREPARATION
- Surface must be clean and dry.
- Remove loose paint and excessive chalk.
- Repair cracks and surface breaks.
- Cover windows, doors, etc. and use caution when applying on windy days.
WARNING
- Avoid contact with eyes and prolonged contact with skin.
- Do notingest. In case of eye contact, flush thoroughly with water. For skin contact, wash with soap and water.
- If swallowed, do not induce vomiting. Drink 1–2 glasses of water and get medical attention.
- KEEP OUT OF REACH OF CHILDREN.
WARRANTY
- A limited 5-year warranty is available on the quality and performance of this product on a per job basis. Contact our technical service department for
details on this warranty program. Otherwise, manufacturer/seller makes no warranty of any kind except that this product is free from defect and is of merchantable quality. - Buyer remedy for breach of warranty is limited to replacement of SEAL-KRETE product or refund of purchase price.
- Convenience Products will not be responsible for labor or the cost of laborfor removal or application of any product.TECHNICAL SUPPORT: For more information on surface prep or application guidelines, or to obtain a Material Safety DataSheet, call 1-800-323-7357, M–F (8:00 am–5:00 pm EST) or visit our website at www.seal-krete.com.
Reviews
There are no reviews yet.